Acidic
Yes

Active Ingredients
Hydrogen peroxide

Antibacterial
Yes

Brand Name
Diversey, Inc

Certifications & Standards
ADA and CCD Compliant
<ul> <li>DFA Cosmetic</li> <li>Kosher</li> <li>Halal</li> <li>USDA</li> </ul>
<ul> <li>FDA Drug</li> <li>Kosher</li> <li>NSF</li> </ul>
<ul> <li>FDA Drug</li> <li>NSF</li> </ul>
ADA
EPA
NSF

Cleaner Size
6" Width x 7" Length

Contact Time
1 Minute
30 Minute
45 Minute
5 Minute

Dilution System
Yes

Directions/Instructions
For General Use: <ul> <li>For use on hard, nonporous inanimate environmental surfaces such as floors, walls, glazed porcelain, glazed ceramic tile, plastic surfaces, shower stalls, bathtubs and cabinets</li> <li>To disinfect inanimate, hard nonporous surfaces, dilute according to label directions.</li> <li>Apply solution with a mop, cloth, sponge or hand-pump trigger sprayer so as to wet all surfaces thoroughly.</li> <li>Allow to remain wet for 10 minutes then remove excess liquid.</li> <li>For heavily soiled areas, a pre-cleaning step is required. Prepare a fresh solution for each use.</li> </ul> For J-Fill® Use: <ul> <li>Insert cartridge into dispenser (see J-FILL® dispenser instructions for proper cartridge placement). Fill small bottle or bucket or use gun to apply a foam directly onto surfaces to be cleaned, scrubbing with a soft brush, pad or cloth. Do not allow foam to dry. Rinse surfaces thoroughly. NOTE: Some commercial strength cleaners are unsuitable for use on some surfaces. Test in an inconspicuous area prior to use.</li> </ul> For RTD® Use: <ul> <li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li> <li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li> <li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li> </ul>
For Regular Use <ul> <li>Spray using full strokes 6-8" (15-20 cm) from surface</li> <li>Wait until stains disappear</li> <li>Wipe with sponge</li> <li>Rinse promptly</li> </ul> For Heavily Soiled Floors <ul> <li>Pour Crew® Tile & Grout Rejuvenator on the area to be cleaned</li> <li>Agitate with a stiff bristled brush and let stand for 15 minutes</li> <li>Repeat agitation and rinse with clean clear water with a mop and let dry</li> </ul> Crew Tile and Grout Rejuvenator easily removes stains as it whitens and brightens discolored grout. Powerful, ready-to-use combination of bleach and detergents power away tough soils and stains such as soap scum, mold, tea and coffee stains. Foaming trigger allows easy application onto vertical surfaces. Bleach-based cleaner with a chlorine scent can be used on most washable surfaces.
Recommended Dilutions: <ul> <li>Heavy Soil, Parts Wash and Immersion Cleaning: 1:24 - 1:32</li> <li>Medium Soil, General Cleaning, Floor Cleaning: 1:64 or 1:128</li> <li>Equipment, Machinery and Pressure Washing Cleaning: 1:128</li> <li>Light Soil, Auto Scrubbing: 1:256</li> </ul> Sprap-and-wipe Cleaning: Spray product onto surface to be cleaned. Wipe surface and rinse. In heavily soiled areas, allow the solution to penetrate for 2-4 minutes. When cleaning glass, ceramic tile, aluminum and painted surfaces, do not allow surface to dry. Rinse thoroughly. Floor Cleaning: Place slippery floor signs around the area. Apply solution onto the floor with a mop or autoscrubber. Pick up all excess solution from the floor. Rinse thoroughly to avoid corrosion. Food Processing Areas: Before using this product in food processing establishments, food products and packaging materials must be removed from the area or carefully protected. After using this product, all surfaces in the area must be thoroughly rinsed with potable water. Avoid contamination of food during use or storage.
Use Instructions <ul> <li>Blockade areas to be stripped. Floors will become very slippery when stripper is applied. Exercise caution.</li> <li>Gloves, goggles and protective footwear is recommended when using this product</li> <li>Dilute or dispense using cold water</li> <li>Apply liberal amounts of stripper solution uniformly to floor with mop. Start at edges to provide more soak time. If splashing occurs, wipe off surfaces with a clean, damp rag.</li> <li>Let stripper solution soak 10-15 minutes. Mop agitate to loosen finish. Re-wet as necessary. Do not allow solution to dry on floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush. Pick up all solution with a clean mop, wet vac, or automatic scrubber. Mop up any 'tracks' left by wet vacs or scrubbers before they dry.</li> <li>Thoroughly rinse floor with clean water, using a mop and bucket. Let floor dry completely before applying a Diversey Green Seal®-Certified finish or other recommended Diversey brand floor finish or sealer.</li> </ul>
Use instructions Mop and Bucket Method <ul> <li>Dust mop or sweep floor.</li> <li>Fill, dilute or dispense product according to label directions.</li> <li>Mop floors. No rinsing is necessary in non-food preparation areas.</li> </ul> Automatic Scrubber Method <ul> <li>Dust mop or sweep floor.</li> <li>Fill, dilute or dispense product according to label directions.</li> <li>Clean and scrub floors.</li> <li>Trail mop machine turns, edges and low spots in the floor to pick up cleaning solution left behind by machine.</li> </ul> Spray and Wipe Cleaning <ul> <li>Fill, dilute or dispense product according to label directions.</li> <li>Spray and wipe surfaces clean.</li> </ul> For RTD® Use: <ul> <li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li> <li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li> <li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li> </ul>
Use instructions <ul> <li>Spray on hard surfaces to be cleaned.</li> <li>Allow power cleaner to penetrate and lift soils.</li> <li>Wipe with a clean cloth.</li> <li>Does not require a water rinse after use.</li> <li>Do not use on glass, aluminum or water-based paint.</li> <li>Suitable for use in areas where food or packaging will not come in contact with spray or surface during or after the use of this product.</li> </ul>
Use Instructions <ul> <li>Use appropriate personal protective equipment</li> </ul> Dilute product as follows: <ul> <li>Light Build-up of Floor Finishes: Dilute product between 1:8 (16 fl. oz. / gal.) and 1:10 (13 fl. oz. / gal.) with cool water</li> <li>Heavy Build-up of Floor Finishes: Dilute product between 1:4 (32 fl. oz. / gal.) and 1:6 (24 fl. oz. / gal.) with cool water</li> <li>Heavy Build-up of Concrete Sealers: Dilute product at 1:2 (64 fl. oz. / gal.) with cool water</li> <li>Blockade areas to be stripped. Floors will be very slippery when stripper is applied. Exercise caution.</li> <li>Apply liberal amounts of solution uniformly to floor with a mop. Start with the edges to give them more soak time. If splashing occurs, wipe off surfaces with a clean rag dampened with water.</li> <li>Let stripper solution soak for 10-15 minutes. Mop agitate to loosen finish or sealer. Re-wet as necessary, do not allow stripper to dry on the floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush</li> <li>Pick-up all of the solution with a clean mop, wet vac or automatic scrubber</li> <li>Mop up any "tracks" left by wet vacs or automatic scrubbers before they dry. Thoroughly rinse floor with clean water, using a mop and bucket.</li> <li>Let floor dry completely before applying recommended Diversey brand floor sealer or finish</li> </ul> Important: <ul> <li>Do not use on wood, linoleum, rubber, marble, painted surfaces, on surface colored and acid dyed concrete floors as this product may harm these surfaces. Test for softening or color bleeding on asphalt floors before using.</li> </ul>
Use instructions <ul> <li>Use BreakDownTM/MC Odor Eliminator on all organic odors and stains.</li> <li>General Deodorizing: Dilute 1:32 with water (4 ounces per gallon/ 31 mL per liter).</li> <li>Washroom: Dilute 1:20 with water (6 ounces per gallon/50 mL per liter). Apply around urinals, toilets, on floors and in trash receptacles.</li> <li>Plumbing Pipes (drains, sinks, disposals, toilets): Pour 4 ounces (120 mL) of BreakDownTM/MC Odor Eliminator into drain pipes 2 times per week when drain flow is lowest.</li> <li>Carpet Odors and Stains for Spotting: Test carpet for colorfastness. Use BreakDownTM/MC Odor Eliminator full strength. Follow good spotting procedures. Re-apply BreakDownTM/MC Odor Eliminator. Let stand 20 minutes.</li> <li>General Carpet Cleaning: Dilute 1:64 with diluted cleaning solution (2 ounces per gallon/15.6 mL per liter).</li> </ul>
Use instructions <ul> <li>Virex® Plus is a one-step, quaternary-based disinfectant cleaner concentrate for use on hard, nonporous surfaces such as floors, walls, glazed porcelain, and plastic surfaces in hospitals, nursing homes, schools, hotels, public areas and other facilities where cleaning and prevention of cross-contamination are critical.</li> </ul> Preparation of Disinfectant Use-Solution <ul> <li>Mix ½ oz. per gallon of water (1:256). Use 1 oz. per gallon of water to kill Norovirus , Enterobacter aerogenes, and Serratia marcescens. Use 2 oz. per gallon of water to kill Adenovirus Type 5 and Type 7.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use-solution with a sprayer, thoroughly wetting surface.</li> <li>Let treated surface remain wet for contact time indicated on label or reference sheet.</li> <li>Wipe dry with a cloth, sponge, or mop, or allow to air dry.</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted</li> </ul> For Use as a Cleaner and Deodorizer <ul> <li>Apply use-solution using a sprayer.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul> For Use as a Non-Acid Toilet Bowl and Urinal Disinfectant/Cleaner <ul> <li>Empty toilet bowl or urinal and apply use-solution to exposed surfaces and under the rim with a sprayer.</li> <li>Brush or swab thoroughly, allow to stand for contact time indicated on the label and flush.</li> </ul> To Control Mold and Mildew <ul> <li>Follow disinfection instructions.</li> <li>Repeat treatment every seven days, or more often if new growth appears.</li> </ul> Dilutable Disinfectant Cleaner <ul> <li>1:256 dilution - Bactericidal, Virucidal, and Fungicidal, in 3 minutes. Kills HIV-1 and Influenza Type A in 1 minute. Some organisms require a 10 minute contact time and/or other dilutions. Please see product label or reference sheet for complete information.</li> <li>1:128 dilution - Kills Norovirus in 5 minutes.</li> </ul>
Automatic Scrubbing Machines1. Dust mop or sweep.2. Blockade areas to be cleaned. Floors will be very slippery until dry.3. Add four (4) oz. per gallon (30mL per liter) of this product to lukewarm water. Scrub floor with product. Trail mop excessive wet areas behind scrubber. Do not rinse floor after cleaning.4. Let floor dry completely.Mop and Bucket Cleaning1. Dust mop or sweep.2. Blockade areas to be cleaned. Floors will be very slippery until dry.3. Add two (2) oz. per gallon (15 mL per liter) of this product to lukewarm water. Mop floor clean with this product. Pick up soil and excess cleaner with a tightly wrung-out cleaning mop. Do not rinse floor after cleaning.4. Let floor dry completely.Stone/Concrete Floor Daily cleaning (Automatic Scrubbing Machine):1. Dust mop or sweep floor.2. Blockade areas to be cleaned. Floors will be very slippery until dry.3. Add (1) oz. per gallon of this product to warm water. Scrub floor with product and Twister™ Intellipad®. Trail mop excessive wet areas behind scrubber. Do not rinse floor after cleaning.4. Let floor dry completely.Stone/Concrete Floor Rejuvenation (Mop and Bucket method):1. Dust mop or sweep floor.2. Blockade areas to be cleaned. Floors will be very slippery until dry.3. Clean floor with a neutral floor cleaner according to label directions. 4. Add thirteen (13) oz. per gallon (101 mL per liter) of this product to lukewarm water. Pick up soil and excess cleaner with a tightly wrung-out cleaning mop. Do not rinse floor after cleaning.5. Let air dry.6. For optimal gloss, burnish the floor with Twister™ Intellipad®.Stone/Concrete Restoration:1. Dust mop or sweep floor.2. Blockade areas to be cleaned. Floors will be very slippery until dry.3. Clean floor with a neutral floor cleaner according to label directions.4. Dilute this product with lukewarm water at a 1:1 dilution ratio. Apply up to 2 coats using a string mop or flat mop until desired shine is achieved. Be sure to evenly cover the entire floor. Do not rinse floor after cleaning.5. Let air dry.6. For optimal gloss, burnish the floor with Twister™ Intellipad®.Best Results<ul><li>Do not use on surfaces colder than 50°F/10°C.</li><li>To avoid contamination, do not return unused product to original container.</li></ul> Note: Floors will be slippery when wet or contaminated with foreign materials.Promptly clean-up spills and foreign materials. Not intended for use in outdoor areas. Meets ASTM D-2047 requirements for slip resistance. Rubber Floors: For optimum appearance, alternate use of this product at standard dilution and ProfiTM/MC Degreaser once desired shine is achieved. On heavily worn rubber floors apply up to three coats of WiwaxTM/MC ProX Maintenance Emulsion using the mop and bucket cleaning instructions with a 1:1 dilution ratio until desired shine is achieved. If high gloss is desired, apply instead, three coats of Carefree® Max ProX Floor Finish.
For General Use:<ul><li>For use on hard, nonporous inanimate environmental surfaces such as floors, walls, glazed porcelain, glazed ceramic tile, plastic surfaces, shower stalls, bathtubs and cabinets.</li><li>To disinfect inanimate, hard nonporous surfaces, dilute according to label directions.</li><li>Apply solution with a mop, cloth, sponge or hand-pump trigger sprayer so as to wet all surfaces thoroughly.</li><li>Allow to remain wet for 10 minutes then remove excess liquid.</li><li>For heavily soiled areas, a pre-cleaning step is required. Prepare a fresh solution for each use.</li></ul> For J-Fill® Use:<ul><li>Insert cartridge into dispenser (see J-FILL® dispenser instructions for proper cartridge placement). Fill small bottle or bucket or use gun to apply a foam directly onto surfaces to be cleaned, scrubbing with a soft brush, pad or cloth. Do not allow foam to dry. Rinse surfaces thoroughly. NOTE: Some commercial strength cleaners are unsuitable for use on some surfaces. Test in an inconspicuous area prior to use.</li></ul> For RTD® Use:<ul><li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li><li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li><li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li></ul> For Command CenterTM/MC Use:<ul><li>Command CenterTM/MC: Attach bottle to Command CenterTM/MC Dispensing System and fill ready to use chemical by actuating touch point (reference Command Center dispenser instructions). Connect hose to cold water tap.</li></ul>
For Prespray Cleaning <ul> <li>Thoroughly vacuum carpet and pre treat spots.</li> <li>Dilute 10 oz. Heavy Duty Prespray with 1 gallon hot water (1 L with 12 L) in pump-up sprayer or fill directly from J-Fill® dispenser.</li> <li>Spray carpet completely, paying particular attention to traffic lanes and spots.</li> <li>Agitate with a carpet rake, extractor brush, shampoo brush or bonnet.</li> <li>Allow 5-10 minutes for Heavy Duty Prespray to completely loosen soils.</li> <li>Thoroughly extract carpet with Extraction Rinse according to use directions. Use Liquid Defoamer in recovery tank if required.</li> </ul> For Bonnet Cleaning <ul> <li>Dilute at 1:32 or 4 oz./gal. (35 mL per L) with warm water.</li> <li>Apply light mist onto carpet bonnet.</li> <li>Bonnet buff carpet with your pad. Flip pad when soiled. When both sides are soiled, rinse or launder.</li> <li>e This solution can also be used for spot treatment. Treat spot, agitate and rinse thoroughly.</li> </ul>
J-Fill® Directions<ul><li> Attach cartridge to J-Fill® Dispensing System (reference J-Fill® dispenser instructions)</li><li> Connect hose to cold water tap</li><li> Product is set to dispense at a 1:120 dilution (Remove tip to obtain a 1:60 dilution. Tip can not be reinserted after removal)</li><li> Actuate dispenser to fill ready-to-use product into buckets or bottles</li><li> Cover or remove all food products from area</li><li> Manual floor cleaning: Apply by mop or brush and scrub. Rinse thoroughly with hot water.</li><li> Note: Wear long rubber gloves for manual cleaning. Rinse metal surfaces immediately.</li><li> Equipment cleaning: Soak parts. Use brush or sponge as necessary. Rinse.</li><li> Note: To avoid food contamination, rinse all surfaces with potable water. Suitable for use in food plants. Do not allow to dry on glass or</li><li> aluminum surfaces.</li><li> For Food Plant Use: All food contact surfaces must be thoroughly rinsed with potable water after treatment with this product. Avoid</li><li> contamination of food during use or storage.</li></ul>
Preparation<ul><li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li>Before the first application of Mainstay® ProX Floor Finish, remove all old finish with any Diversey stripper.</li></ul>Coating<ul><li>Apply 3-4 medium coats of Mainstay® ProX Floor Finish with a clean finish mop. Let dry to the touch between coats (about 30 minutes).</li><li>On porous resilient or stone floors, seal first with 2 coats of the recommended Diversey sealer.</li></ul>Maintenance<ul><li>For daily cleaning dust mop or sweep.</li><li>Then wet clean with recommended Diversey cleaner in an autoscrubber or with a damp mop.</li></ul>Burnishing<ul><li>To renew gloss, spray buff as needed with recommended Diversey spray buff, a red or beige pad and a 175-1500 rpm machine. Or burnish with a UHS pad and a battery, cord electric or propane machine at 1500-2000+ rpm.</li></ul>Recoating<ul><li>Dust mop or sweep floor. Scrub floor with an autoscrubber or floor machine using a blue pad and the recommended Diversey cleaner at therecommended dilution. Rinse well and let dry.</li><li>Apply 1-2 new coats of Mainstay® ProX Floor Finish.</li></ul>
Specs & Application Instructions: <ul> <li>Use where odors are a problem</li> <li>Can be used in hospitals, nursing homes, schools and colleges, offices, public areas and restrooms</li> <li>Use on hard, non-porous restroom surfaces: glazed ceramic tile, glazed porcelain, chrome, stainless steel and plastic surfaces associated with floors, walls, fixtures, toilets, urinals, sinks, shower rooms and locker rooms.</li> </ul>
Specs & Application Instructions:<ul><li> A no-rinse sanitizer that conveniently and effectively sanitizes food contact surfaces where sanitization is of prime importance</li><li> For use on surfaces, utensils and equipment</li><li> Use in commercial sinks for sink immersion of utensils</li></ul>
Use instructions <ul><li> Dispense proper strength solution of product and warm or hot water in a mop bucket. Sweep up and remove solid waste from floor before applying.</li><li> Post "Wet Floor" signs around area to be cleaned and use a clean mop to apply the cleaning solution generously to the floor, overlapping mop strokes. For best results, scrub the floor with a brush, especially if the floor has grout.</li><li> Repeat if necessary on heavily soiled areas. Pick up soil and excess solution with a tightly wrung out mop, wringing it out frequently, or squeegee to floor drain.</li><li> Dry mop or squeegee floor dry or allow floor to air dry before reuse. Once dry, remove "Wet Floor" signs. A potable water rinse is only required for those surfaces that may contact edible product. Pour unused Bio-Floor Cleaner from mop bucket into kitchen floor drain for daily maintenance.</li></ul> NOTE: Floors will be slippery when wet or contaminated with foreign materials. Promptly clean up spills and foreign materials. See container for lot number.Storage: Do not store in food processing or food storage areas. Shake well before using if product has settled.For Food Plant Use: Not for use on food contact surfaces. Avoid contamination of food during use or storage.
Use Instructions <ul><li> Preparation of Disinfectant Use-Solution: Add 2 oz. per gal. of water (1:64).</li></ul>Disinfection/Virucidal/Fungicidal/Mold and Mildew Control Directions <ul><li> Apply use-solution to hard, non-porous surfaces, thoroughly wetting the surfaces, with a cloth, mop, sponge, sprayer or by immersion. Treated surfaces must remain wet for 10 minutes. Wipe dry with a cloth, sponge or mop or allow to air dry.</li><li> For heavily-soiled areas, a preliminary cleaning is required.</li><li> Rinse all surfaces that come in contact with food such as countertops, appliances, tables and stovetops with potable water before reuse. Do not use on utensils, glassware and dishes.</li><li> For sprayer applications, use a coarse spray device. Spray 6 - 8 inches from surface; rub with brush, sponge or cloth. Avoid breathing spray.</li><li> For fungicidal activity, this product is an effective fungicide against Trichophyton mentagrophytes (the athlete's foot fungus) in areas such as locker rooms, dressing rooms, shower and bath areas and exercise facilities. This product is a one-step fungicide at 2 oz. per gal. of water in 200 ppm hard water and 5% serum.</li><li> For mold and mildew: At 2 oz. per gallon, this product will effectively inhibit the growth of mold and mildew and the odors caused by them when applied to hard, non-porous surfaces. Follow disinfection instructions. Repeat treatment every seven days, or more often if new growth appears.</li><li> This product is not for use on medical device surfaces.</li><li> Prepare a fresh solution daily or more often if the use solution becomes visibly diluted or soiled.</li></ul>Non-Acid Toilet Bowl and Urinal Disinfectant/Cleaner Directions<ul><li> Remove gross filth prior to disinfection.</li><li> From Use Solution: Empty toilet bowl or urinal and apply a 2 oz. per gallon use-solution to exposed surfaces and under the rim with a cloth, mop, sponge or sprayer. Brush or swab thoroughly, allow to stand for 10 minutes and flush.</li><li> To Clean and Deodorize: Mix 2 oz. per gallon of water to clean and deodorize surfaces. Apply using a cloth, mop, sponge or sprayer. Wipe or allow to air dry</li></ul>
Preparation<ul><li data-list="bullet">Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li data-list="bullet">Strip floors using a Diversey brand stripper per the instructions on the stripper label.</li></ul>Coating<ul><li data-list="bullet">Apply 3 or more medium coats of product using a clean finish mop or the Diversey ProSpeed TM/MC or TrailBlazer TM/MC Floor Finish Applicator Systems. Apply additional coats until desired gloss is obtained.</li><li data-list="bullet">Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li></ul>Maintenance<ul><li data-list="bullet">Dust mop or sweep.</li><li data-list="bullet">Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to the label directions.</li><li data-list="bullet">Burnish using appropriate pads.</li></ul>Recoating<ul><li data-list="bullet">Dust mop or sweep.</li><li data-list="bullet">Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li><li data-list="bullet">Blockade area and apply 1-2 uniform coats of finish using a clean mop.</li><li data-list="bullet">Allow finish to cure for 24 hours before burnishing.</li></ul>
Bona SuperCourt Cleaner Concentrate ratio is 1:128 (128 parts water to 1 part concentrate).1. Remove the caps from the bottle and foil seals underneath each cap. 2. Replace both caps and tighten. 3. Grasp the bottle by the handle and tilt forward filling the concentrate into the reservoir. 4. Measure the amount of concentrate by using the one-ounce graduation marks on the front of the reservoir. 5. Remove the cap on top of the reservoir and pour the measured concentrate into the desired tank, bucket or bottle. 6. Fill the remaining tank, bucket or bottle volume with cold water. 7. Repeat as needed. Dispose of excess or unused products in accordance with local, state and federal requirements.
Mop and Bucket Method<ul><li> Dust mop or sweep floor.</li><li> Fill, dilute or dispense product according to label directions.</li><li> Mop floors. No rinsing is necessary in non-food preparation areas.</li></ul>Automatic Scrubber Method<ul><li> Dust mop or sweep floor.</li><li> Fill, dilute or dispense product according to label directions.</li><li> Clean and scrub floors.</li><li> Trail mop machine turns, edges and low spots in the floor to pick up cleaning solution left behind by machine.</li></ul>Spray and Wipe Cleaning<ul><li> Fill, dilute or dispense product according to label directions.</li><li> Spray and wipe surfaces clean.</li></ul>For RTD® Use:<ul><li> Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li><li> Wipe with clean cloth or towel to dry. Dilute with cold water.</li><li> To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li></ul>
Step 1: Flush toilet before cleaning and drop one Easy Pak in the toilet bowl.Step 2: Wait for product to dissolve and foam in the water. While you wait, it is recommended to clean the outside of the toilet with a spray and wipe cleaner.Step 3: With a toilet brush, swab the inside of the bowl to clean the side walls and under the rim. After the cleaning process is complete, flush the toilet to remove cleaning solution before the next use.CONTAINS NO PHOSPHORUSNote: Do not remove packets before use. Do not handle packets with wet hands. Reseal container after removing packets. Store in a cool, dry place. Keep from freezing.
This product can be used in multiple areas including operating rooms, long-term care facilities, medical facilities, animal treatment facilities, cruise ships, hotels, public buildings, public restrooms, recreational facilities, retail businesses and schools (colleges and universities), and is compatible with most hard, non-porous surfaces.
To clean bowl and urinals <ul><li>Squeeze bowl cleaner on all porcelain surfaces. Cover all recesses and areas where stains can build-up under the rim, water outlets and drain pipe openings (30 mL). </li><li>Allow bowl cleaner to dwell (10 minutes recommended). </li><li>Swab and flush rinse.</li></ul>
<ul> <li>A highly effective cleaner designed to remove soils and oils without dulling or altering the appearance of your floor</li> <li>Designed for use on most floor types</li> <li>Part of a comprehensive floor care offering for cleaning, maintaining, stripping and finishing floors</li> </ul>
<ul> <li>Add the product at ½ oz. per gallon of water (1:256).</li> <li>Pre-clean heavily soiled areas.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use solution to hard, non-porous environmental surfaces. To disinfect, all surfaces must remain wet for 10 minutes.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul> Note: Rinsing is not necessary unless floors are to be coated with finish or restorer. All food contact surfaces such as appliances and kitchen countertops must be rinsed with potable water. Do not use on glassware, utensils or dishes For Use as a Cleaner and Deodorizer <ul> <li>Apply use solution to hard, non-porous surfaces. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li> </ul> For Use as a Non-Acid Bowl Cleaner/Disinfectant in Toilet Bowls and Urinals from Use-Dilution Empty toilet bowls by forcing water through the trap. Apply use solution to exposed surfaces in toilet bowls and urinals. Swab entire surface area especially under rim. Allow entire surface to remain wet for 10 minutes. Flush toilet or urinal and rinse swab applicator thoroughly. For Use to Clean and Disinfect Shower Rooms, Locker Rooms and Other Large, Open Areas with Floor Drains <ul> <li>Apply use solution to floors, walls and ceilings. All surfaces must remain wet for 10 minutes. Scrub and rinse surfaces thoroughly and let air dry</li> </ul> To Kill Mold, Mildew and Fungi (in 5% soil load) <ul> <li>Apply use solution to hard, non-porous environmental surfaces and allow surfaces to remain wet for 10 minutes. Wipe and let air dry</li> </ul> To Control Mold and Mildew <ul> <li>Apply use solution to pre-cleaned hard, non-porous environmental surfaces and allow to air dry. Repeat weekly or when growth reappears</li> </ul>
<ul> <li>Available in dilution control for ease in use, safety and cost control</li> <li>Can also be used for carpet spotting and extraction cleaning</li> <li>Use in autoscrubbers, mop and bucket and spray-and-wipe applications</li> </ul>
<ul> <li>Dispense Crew® Bathroom Cleaner and Scale Remover using cold water at 1:18 into spray bottle.</li> <li>Apply ready-to-use solution on a damp cloth or spray directly on surface to be cleaned and let dwell for several seconds</li> <li>Rub surface with cloth or non-abrasive cleaning pad.</li> <li>Rinse surface with clear, cold water.</li> <li>Polish with a dry soft cloth.</li> <li>Do not use on wood or marble.</li> <li>Test in an inconspicuous area since certain surfaces may be unsuitable for commercial strength cleaners</li> <li>Always stand on a non-slip surfaces when in shower or tub.</li> </ul>
<ul> <li>Spray & wipe cleaner for hard surfaces</li> <li>Use to remove marker and paint</li> <li>Cleaner/Degreaser for shops and kitchens NSF C-1</li> </ul>
<ul> <li>Spray on hard, nonporous surfaces and equipment</li> <li>Use in commercial sinks for sink immersion of utensils</li> <li>Use in dairies, restaurants, bars and institutions where sanitation is of prime importance</li> </ul>
<ul> <li>Spray surfaces and let solution remain on surface for a minimum of 5 minutes</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted</li> </ul> Dilutable Disinfectant Cleaner <ul> <li>1:16 dilution - Virucidal, Bactericidal, and Fungicidal, including antibiotic resistant bacteria, in 5 minutes</li> <li>1:128 dilution - Non-food contact sanitizer in 3 minutes or general purpose cleaning</li> <li>1:256 dilution - Floor and general purpose cleaner</li> </ul> Note: Rinsing is not necessary unless floors are coated with finish or restorer.All food contact surfaces must be rinsed with potable water. Do not use on glassware, utensils or dishes. Prior to first use on a particular surface, it is recommended to test in a small, discreet area if there is concern of incompatibility, or contact a Diversey representative. Not recommended for floors at dilution 1:16. Refer to product label for complete use instructions.
<ul><li data-list="bullet">Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li data-list="bullet">Strip floors, using a Diversey stripper per the instructions on the stripper label.</li></ul>Coating<ul><li data-list="bullet">Apply 3 or more medium coats using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li><li data-list="bullet">Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li></ul>Maintenance<ul><li data-list="bullet">Dust mop or sweep. Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li><li data-list="bullet">If desired, dry buff using medium to aggressive pad and 1000- 500 rpm equipment. Ultra-high speed burnish using a medium aggressiveness pad and 2000+ rpm equipment.</li></ul>Recoating<ul><li data-list="bullet">Dust mop or sweep.</li><li data-list="bullet">Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li><li data-list="bullet">Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before burnishing.</li></ul>Removal<ul><li data-list="bullet">Remove using recommended Diversey brand stripper following label directions.</li></ul>Precautions<ul><li data-list="bullet">Do not dilute. Do not use on surfaces colder than 50°F (10°C) @ 15% RH. To avoid contamination, do not return unused finish to original container. Do not freeze.</li></ul>
<ul><li data-list="bullet">Blockade areas to be stripped or finished. Position wet-floor signs around area to be cleaned.</li><li data-list="bullet">Strip floor using recommended Diversey brand stripper according to label directions</li></ul>Coating<ul><li data-list="bullet">Apply 2-3 uniform coats using a clean finish mop or the TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li><li data-list="bullet">Allow 30 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before buffing.</li></ul>Maintenance<ul><li data-list="bullet">Dust mop or sweep</li><li data-list="bullet">Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner following label directions</li><li data-list="bullet">If desired, spray buff using recommended Diversey brand floor maintainer to enhance gloss</li></ul>Recoating<ul><li data-list="bullet">Dust mop or sweep</li><li data-list="bullet">Deep scrub floor using Diversey cleaner according to label directions</li><li data-list="bullet">Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before buffing.</li></ul>Removal<ul><li data-list="bullet">Remove using recommended Diversey brand stripper according to label directions</li></ul>Best Results<ul><li data-list="bullet">Do not dilute</li><li data-list="bullet">Do not use on surfaces colder than 50°F (10°C) @ 15% RH</li><li data-list="bullet">To avoid contamination, do not return unused product to original container</li></ul>Note: Floors will be slippery when wet or contaminated with foreign materials. Promptly clean-up spills and foreign materials. Meets ASTM D2047 requirements for slip resistance.
<ul><li> Fill, dilute or dispense product into spray bottle according to label directions</li><li> Spray onto surfaces to be cleaned. </li><li> Wipe surface with clean cloth or dry towel. </li><li> Do not use on copper or brass as repeated use may discolor these surfaces.</li></ul>
<ul><li> For use as daily floor cleaner and general cleaner.</li><li> Use as spray and wipe application or in mop and bucket.</li><li> Use in autoscrubber.</li></ul>
<ul><li> Product will be automatically dispensed by the dishmachine dispenser during the machine cycle</li><li> To wash dishes, preflush and/or scrape dishes before washing</li><li> Rack dishes properly and place racked dishes inside dishmachine</li><li> Wash, rinse and sanitize dishes as directed by your Diversey representative</li><li> Remove rack from dishmachine and allow dishes to air dry</li><li> For Food Plant Use: Avoid contamination of food during use or storage. Cookware or utensils and other equipment and surfaces subject to direct contact with food must be thoroughly rinsed with potable water prior to re-use.</li></ul>
<ul><li> Responds beautifully to conventional, high-speed or UHS equipment and maintenance procedures</li><li> May require a sealer on highly polished stone, glazed clay tile, and some rubber floors</li><li> Not intended for use on cork, wood, or bamboo flooring unless specified by the manufacturer</li></ul>
<ul><li> Use 1.0 mL to 3 mL per liter (0.128 to 0.384 oz./gal.) of water, depending on water hardness and soil conditions. </li><li> Feed automatically into the dishmachine using a Diversey dispensing system. </li><li> Contact your Diversey representative for correct set-up and operating conditions for your operation. </li><li> Store at room temperature and avoid freezing. </li><li> Do not use on aluminum or other soft metals. </li></ul>
<ul><li> Use as a daily floor cleaner on most floor types</li><li> Can also be used as a high performance general purpose cleaner</li></ul>
<ul><li> Use for glass and mirror cleaning</li><li> Can be used on multi-surfaces</li></ul>
<ul><li> Dust mop or sweep</li><li> Dilute, dose or dispense product into spray bottle, mop bucket or autoscrubber using cold water</li></ul>Mop and Bucket Floor Cleaning<ul><li> Mop floors; no rinsing is necessary</li><li> Pick up excess cleaner with lightly wrung-out mop</li></ul>Automatic Scrubber Floor Cleaning<ul><li> Scrub with red pad daily</li><li> Double-scrub with green/blue pad before recoating or restoring. Trail mop machine turns, edges and low spots to pick-up cleaning solution</li></ul>Left behind by machine Floors will be slippery when wetSpray and Wipe Cleaning<ul><li> Spray, wipe and allow surface to dry</li></ul>
<ul><li> For best results, always vacuum carpet first.</li><li> Fill extractor solution tank with Extraction Rinse SC solution from dispenser.</li><li> Light duty: As needed, pre-spot with the appropriate spotter. Extract following equipment maker's operating instructions.</li><li> Medium to Heavy Duty: As needed, pre-spot with the appropriate spotter. Fill pressure sprayer with Soil Release/Bonnet Buff solution on traffic lanes and soiled areas of carpet and allow to dwell for a few minutes.</li><li> Before solution dries, extract carpet in normal manner.</li></ul>Note: If being used for the first time, test for colorfastness in an inconspicuous area before use.
<ul><li> Spray on hard surfaces to be cleaned.</li><li> Allow power cleaner to penetrate and lift soils.</li><li> Wipe with a clean cloth.</li><li> Does not require a water rinse after use.</li><li> Do not use on glass, aluminum or water-based paint.</li><li> Suitable for use in areas where food or packaging will not come in contact with spray or surface during or after the use of this product.</li></ul>Maxflow feedline required for accurate dilution of J-Fill®
<ul><li>Apply Heavy Duty Prespray according to use directions, depending on soil level.</li><li>For synthetic carpets, dilute 1 oz. Extraction Rinse with 1 gal. luke warm water (30 mL per 3.8 L) in extractor. Dilute 1 oz. with 5 gal.(30 mL per 19 L) water for wool carpets (use cool water).</li><li>Thoroughly extract carpet.</li><li>Groom carpet with clean carpet rake or stiff synthetic broom and allow to air dry.</li></ul>Note: If being used for the first time, test for colorfastness in an inconspicuous area before use.
<ul><li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li><li>Strip floor using a Diversey stripper per the instructions on the stripper label.</li></ul>Coating<ul><li>Apply 1 to 2 coats of Over & Under® ProX floor sealer using a clean mop.</li><li>Allow 30 minutes drying time between coats. Temperature, humidity and ventilation may aect drying time. Allow finish to cure for 24 hours before burnishing.</li><li>Apply 1 or more coats of recommended floor finish according to label directions.</li></ul>Burnishing<ul><li>Dust mop or sweep floor.</li><li>Clean the floor with mop or automatic scrubber using the recommended cleaner according to label directions.</li><li>Maintain the finish gloss using periodic recoating, spraybung or burnishing according to finish label.</li></ul>Removal<ul><li>Remove using recommended stripper according to label directions.</li></ul>For Best Results<ul><li>Do not dilute.</li><li>Do not use on surfaces colder than 50 degrees F/10 degrees C.</li><li>To avoid contamination, do not return unused product to original container.</li></ul>Note: Floors will be slippery when wet or contaminated with foreign materials. Promptly clean up spills and foreign materials. Not intended for use in outdoor areas. Meets ASTM D-2047 requirement for slip resistance.
<ul><li>Clean and disinfect high-touch surfaces in just ONE Minute</li><li>Non-irritating to eyes and skin</li></ul>
<ul><li>Designed for industrial and institutional classifications</li><li>Suitable for use in all water types from soft to hard</li></ul>
<ul><li>Dust mop or sweep floor.</li><li>Dilute, dose or dispense product into spray bottle, mop bucket or autoscrubber using cold water.</li></ul>Mop and Bucket Floor Cleaning<ul><li>Mop floors; no rinsing is necessary.</li><li>Pick up excess cleaner with lightly wrung-out mop</li></ul>Automatic Scrubber Floor Cleaning <ul><li> Scrub with red pad daily. </li><li>Double-scrub with green/blue pad before recoating or restoring. Trail mop machine turns, edges and low spots to pick-up cleaning solution left behind by machine. </li><li>Floors will be slippery when wet. </li></ul>Spray and Wipe Cleaning <ul><li>Spray, wipe and allow surface to dry.</li></ul>
<ul><li>Use as floor conditioning and neutralizing before applying finish.</li><li>Effective at counteracting urine odors on hard floors, grout and carpeting</li><li>Suitable for use in non-food processing areas</li></ul>
Specs & Application Instructions: <ul><li> Spray on hard, nonporous surfaces and equipment</li><li> Use in commercial sinks for sink immersion of utensils</li><li> Use in dairies, restaurants, bars and institutions where sanitation is of prime importance</li></ul>
Virex® Plus is a one-step, quaternary-based disinfectant cleaner concentrate for use on hard, nonporous surfaces such as floors, walls, glazed porcelain, and plastic surfaces in hospitals, nursing homes, schools, hotels, public areas and other facilities where cleaning and prevention of cross-contamination are critical. Preparation of Disinfectant Use-Solution <ul> <li>Mix ½ oz. per gallon of water (1:256). Use 1 oz. per gallon of water to kill Norovirus , Enterobacter aerogenes, and Serratia marcescens. Use 2 oz. per gallon of water to kill Adenovirus Type 5 and Type 7.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use-solution with a sprayer, thoroughly wetting surface.</li> <li>Let treated surface remain wet for contact time indicated on label or reference sheet.</li> <li>Wipe dry with a cloth, sponge, or mop, or allow to air dry.</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted.</li> </ul> For Use as a Cleaner and Deodorizer <ul> <li>Apply use-solution using a sprayer.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul>

Dispensing Quantity
0.01 fl oz to 0.03 fl oz Per Stroke

Floor Type
Ceramic Tile
Stone

Form
Lotion

Fragrance Classification
10.40" x 11"
Alcohol
Fragrance-free
Lemon Tea Splash

Freshener/Sanitizer Type
Liquid
Spray

Freshener/Sanitizer Volume
32 fl oz (1 quart)
84.5 fl oz (2.6 quart)

Kill Claims
Hepatitis B Virus (HBV)
HIV-1 Human Immunodeficiency Virus Type 1
Methicillin-resistant Staphylococcus Aureus (MRSA)
Microorganism
Norovirus
Severe Acute Respiratory Syndrome Coronavirus (SARS-CoV)
Tuberculosis (TB)

Manufacturer Part Number
Spot Remover

Marketing Information
Body

Moisturizing
Yes

Non-Acidic
Yes

Operating Mode
Automatic/Manual
Manual

Packaged Quantity
Art
Document

Pad Diameter
14"
20"
5"
6"

Pad Shape
Round

Pad Width
14"

Pest Control
Wasp

Pesticide Type
Spray

Pesticide Volume
15 fl oz

Product Material
ABS Plastic
MicroFiber
Plastic
Steel

Recycled Content
0%

Skin Type
Dry

Sprayer Type
Trigger

Popular tags

View all

Diversey, Inc

View as Grid List

Sort by

Display per page

Diversey Lite Touch CRT & Plexiglas Cleaner

DVO03970

For Multi Surface, Multipurpose - 1 quart - Sturdy, Ammonia-free, Solvent-free, Fragrance-freeSpray Bottle - 1 Each - Purple

$113.75 $65.20

Diversey BreakDown Odor Eliminator

DVO94355110CT

Concentrate Liquid - 128 fl oz (4 quart) - Cherry Almond Scent - 4 / Carton - Red

$243.08 $148.88

Diversey Care Wiwax Cleaning/Maintenance Emulsion

DVO101110064

For Multi Surface - Concentrate - Liquid - 128 fl oz (4 quart) - 8.5 pH - Characteristic Scent - White Bottle - 1 Each

$60.42

Diversey Empty Spray Bottle for Cleaner

DVOD03905CT

Suitable For Restroom, Floor - Easy to Use, Labeled - 12 / Carton - Clear

$54.96

Diversey IntelliCare Refill Foam Body Wash

DVO100907877CT

Lemon Tea Splash, Citrus Scent - 44 fl oz (1300 mL) - Cartridge Dispenser - Kill Germs, Dirt Remover - Hand, Body, Washroom, Hair - Pink - pH Balanced, Bio-based - 2 / Carton

$178.50 $116.22

Diversey Spray Bottle

DVOD100863672CT

Disinfectant - Clear - 12 / Carton

$54.00