Middle Tenessee Office Products 2. Carpet Cleaners

Directions for UseRecommended for use on all types of resilient tile flooring and properly prepared hard surfaces.RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco&#174; stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance.ROUTINE MAINTENANCE:Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco&#174; One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating.INTERIM MAINTENANCE:Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above.Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum

For Use on Floors: <ul> <li>Dilute ¼ cup Murphy Oil Soap in 1 gallon of warm water</li> <li>For heavy cleaning dilute ½ cup Murphy Oil Soap per gallon </li> <li>Clean with well wrung-out mop, and mop any excess water</li> <li>No rinsing required.</li> </ul> Other Surfaces: Wet cloth with diluted Murphy Oil Soap liquid. Wipe clean to reveal wood's natural beauty

Pro-Tip: For use as in facilities with black asphalt type flooring, such as U.S. Postal Facilities.

Pro-Tip: Use for ordinary scrubbing of floor by hand or for automatic floor-scrubbing machines. Also used on walls, tables and all other hard surfaces.

Drop one PAC into a bucket filled with 1.6 gallons of warm water. After the satisfying fizz subsides, you're ready to mop. Simply mop all your hard surface floors as you normally would and enjoy the streak-free results. Not intended for use with spray mops. Keep out of the reach of children.

Recommended for polished concrete and terrazzo surfaces for extended stain and etch protection. Clean entire area with Betco DensiClean, allow floor to dry prior to application. Apply Betco LiquiShield at proper application rate, 3,000 to 4,000 sq. ft. per gal, with a low-pressure sprayer spread with a microfiber applicator pad or mop and bucket application. Allow to dry to touch, 45 to 60 minutes, then apply second coat using the same procedures. Allow second coat to dry 60 minnutes then high speed burnish with Betco Si Burnish Pad. Allow 1 to 2 hours cure time before floor is exposed to full traffic. Allow 24 hours before the use of cleaners on the floor. Maintain floor with Betco Crete Rx DensiClean and Betco Crete Rx Cleaning Pads for maximum protection and shine.

Recommended for top scrubbing all types of water-based acrylic floor finishes and sealers on all types of resilient tile (vinyl composition, vinyl and linoleum). To be used as a top scrub cleaner in preparing a coated floor surface for recoating. Dilute Best Scrub 8 1/2 oz./gal. or 65 mL/L (1:15). Apply solution to floor using a mop or automatic scrubber. Agitate solution using a green cleaning pad or brush. Remove solution from the floor with a mop, wet vacuum, or automatic scrubber. When removed properly no flood rinsing is required. After the floor has dried check for residue. If any residue is present a rinse will be needed. If initial scrubbing does not remove embedded dirt, the floor may need additional scrubbing or may require stripping.

Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. ROUTINE MAINTENANCE: Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco® One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE: Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.

Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply floor finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. ROUTINE MAINTENANCE: Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco® One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE: Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.

<ul><li> For use as a powerful rinse aid</li><li> Safe to use on all colorfast carpets</li></ul>

<ul><li> Recommended ESIor removing water-based acrylic floor finishes from all types of resilient tile and hard surfaces. Pre-test in a small area; color bleeding or discoloration may occur on linoleum, rubber tile or asphalt tile.</li><li> Not recommended for stripping linoleum or sheet vinyl floors.</li><li> Sweep or dust mop the floor to remove any large debris. Dilute with warm to hot water.</li><li> For normal stripping, dilute 13 oz./gal. or 100 mL/L (1:10) of water.</li><li> For heavy stripping, dilute 25 oz./gal. or 200 mL/L (1:5) of water.</li><li> Apply solution liberally to floor surface. Allow a minimum of 5 minutes contact time. Be sure to keep surface wet at all times. Agitate with a low-speed rotary machine, automatic scrubber or stripping machine. Pick up the solution with a wet vacuum, an automatic scrubber or a mop and bucket and thoroughly rinse the floor. Allow floor to dry completely before applying finish or sealer. No flood rinsing is necessary if surface appears free of dust and residue. Please recycle empty container.</li></ul>

<ul><li> Responds beautifully to conventional, high-speed or UHS equipment and maintenance procedures</li><li> May require a sealer on highly polished stone, glazed clay tile, and some rubber floors</li><li> Not intended for use on cork, wood, or bamboo flooring unless specified by the manufacturer</li></ul>

<ul><li> Use as a daily floor cleaner on most floor types</li><li> Can also be used as a high performance general purpose cleaner</li></ul>

Recommended for mopping or autoscrubbing finished floors. Can also be used as a spray and wipe cleaner on appliances, desks, plastic, stainless steel and painted surfaces. <ul> <li>Dilute 0.5 US oz./US gal. or 4 mL /L of water, depending on soil conditions.</li> <li>Apply cleaning solution using a mop or autoscrubber.</li> <li>Pick up the solution. Rinsing is not required except in very dirty situations .</li> <li>Allow floor to dry thoroughly.</li> </ul>